Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Deep groove ball bearing is the most representative rolling bearing，versatile。Suitable for high speed or even very high speed operation，And very durable.，No frequent maintenance required。The friction coefficient of this kind of bearing is small，Limit speed height， Simple structure，Low manufacturing cost，Easy to achieve high manufacturing accuracy。 Varied in size range and form，Application in precision instrumentation、Low noise motor、CARS、Motorcycle and general machinery industries，It is the most widely used type of bearing in the machinery industry。Mainly bear radial load，It can also withstand a certain amount of axial load Deep groove ball bearings are the most commonly used rolling bearings。Its structure is simple，Easy to use。It is mainly used to bear radial loads，But when the bearing radial clearance is increased，It has certain angular contact ball bearing performance，Tolerable diameter、Axial combined load。When the speed is high and it is not suitable to use thrust ball bearings，It can also be used to
2017-06-14 Reading quantity 255
introduction：NACHIBearing is a bearing product with high performance，Its used in a lot of areas。The use conditions of this bearing are more rigorous，To achieve the required environment before operating，Thats how you get the best results。Before we use this bearing，To determine the use of the site and the use of the premise and situation，Select specifications size、Precision scheduling。
2017-06-22 Reading quantity 245
introduction：Bearings belong to the category of linear motion systems，Its manufacturing cost is very low，Under normal circumstances, it must be used in combination with bearings，Linear bearing load is relatively small，The steel ball, on the other hand, uses very little friction to spin，To operate with maximum precision
2017-06-06 Reading quantity 279
introduction：The biggest advantage of bearings is that the friction is not as large as that of joint bearings，Although linear bearings themselves have a certain amount of friction，But in general, normal friction is inevitable，But if there is abnormal friction, you need to be alert，Because when the linear bearing has abnormal friction, it will not only lose a lot of energy，It will also cause friction damage to the surface of the linear bearing。
2017-06-06 Reading quantity 295
introduction：Bearing due to the use of different environments，Different erosion modes，So erosion behaves differently。Linear bearings, of course, can not escape this fate of erosion，What are the three ways that linear bearings are eroded
2017-06-05 Reading quantity 271
introduction：How to reduce the consumption of mill bearings。 one、Make good use and damage of rolling mill bearings...
2016-04-01 Reading quantity 1866
introduction：Lubrication and maintenance of rolling mill bearings，Bearings are lubricated by using an oil film to separate rolling surfaces in relative motion from each other，It will not fail due to excessive wear caused by rough point contact。
2017-05-28 Reading quantity 243
introduction：It consists of a magnetic circuit section、Contact component，The magnetic circuit part consists of an iron core、armature、Yoke iron、Shorting ring、A coil and a tension spring are composed，It is characterized by a side plate mounted on an iron core between the coil and the yoke iron，And side plate with iron core、Yoke iron contact is good。The utility model is based on the original relay A side panel made of pure copper was added to the base，The side panels can be used on the electromagnetic system The magnetic leakage is short-circuited,Reduced vortex wastage,Greatly reduces the AC end when the relay coil is overloaded,Reduced relays for other electrons Interference of equipment,Improved contact reliability。
2017-03-16 Reading quantity 357
introduction：Screw support seat installation procedure，A coupling will be used to connect the motor to the ball screw。(Pay attention to installation accuracy)
2017-05-19 Reading quantity 282
introduction：In all cases of premature failure，approximately16％It is caused by improper installation or use of incorrect installation methods。Various applications may require the use of machinery、Heat or hydraulic mounting method to install correctlyINAbearing。Choosing the installation method suitable for the application will help you extend your timeINAbearing’Service life，Concurrent reduction of causeINAThe cost of premature bearing failure and potential damage to the application。
2015-06-23 Reading quantity 1675
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
