Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Main use Local host、Auxiliary engine、The electric control box consists of three parts。With wind selection、screenless、netless、Uniform particle size and other properties，The production process is continuous。The machine has reached the international advanced level，It is widely used in pharmaceuticals、Chemical engineering、Material crushing in food and other industries。 Working principle The material enters the crushing chamber from the hopper through the screw conveyor，It is cut and shredded by a high-speed rotating blade，The material is transported into the cyclone by the method of negative pressure air transport、Bag type dust collector，Discharge material to meet product requirements。 Technical parameter Model number
2015-02-06 Reading quantity 2803
introduction：Under normal circumstances，Double row deep groove ball bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The temperature should be at30℃around，The maximum temperature shall not exceed70Degree Celsius，Or else，Will cause deformation due to high bearing temperature，In serious cases, it will cause direct damage to the jaw crusher，What is more，Directly causing the machine to explode。therefore，Always be aware of the jaw pose
2015-02-06 Reading quantity 1561
introduction： Rolling bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]In the course of its use, it shows strong regularity，And repeatability is very good。Normal quality bearing(Rolling bearing)At the beginning of use，Vibration and noise are relatively small，But the spectrum is a little scattered，The amplitude is small，Probably due to some defect in the manufacturing process，As shown in table
2015-02-06 Reading quantity 1560
introduction：lishi zuanchuang Vertical drilling machine vertical drilling machine Drill press with vertical spindle and fixed center position,Short vertical drill(figure1[Vertical drilling machine])。It is often used in machinery manufacturing and repair factory processing、Holes for small workpieces。 Before processing，The position of the workpiece on the workbench must be adjusted first，Align the center line of the machined hole with the axis of the tool。Processing time，The workpiece is fixed，The spindle rotates in the sleeve and feeds axially with the sleeve。Table and headstock can be adjusted along column guide rails，To accommodate different heights
2015-02-06 Reading quantity 2814
introduction： High alloy die steels contain high chromium and medium chromium tool steels、High speed steel、Matrix steel。This kind of steel contains more alloying elements，Good hardenability、High wear resistance and small quenching deformation，Widely used to withstand large loads、Large production batch、Molds requiring high wear resistance and complex shapes。 （1）High carbon high chromium steel The composition of this steel is characterized by a high chromium content、High carbon content，It is the most widely used in cold working die steel、The largest number。Typical steel numbers areCrl2、Crl2MoV、Crl2MolVl (D2)、Crl2WEtc.。
2015-02-06 Reading quantity 1554
introduction： bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Failure in operation is a common occurrence，So dont be surprised。Out of order，Judgment and handling is key。Today were going to talk about itFAGbearing[FAGbearing:The main shaft bearing is made of a solid inner ring、Outer ring、The ball、And with solid window cage
2015-02-06 Reading quantity 1623
introduction：Wedge joint A detachable joint that uses a wedge to unite the connected parts(See picture Wedge and wedge connection )﹐It is mainly used to transfer axial force﹐Torque transfer is also possible。Wedge connection can be divided into two kinds: loose connection and tight connection。The loose wedge has no inclination﹐Loose fit in the wedge hole﹐Only one-way axial force can be transmitted。A tight wedge with a slope on one or both sides﹐Tighten the wedge during assembly﹐There is assembly stress between the connections﹐They can squeeze together and become one﹐Therefore, it can transmit the axial force of repeated action。The tight wedge slope must ensure that the wedge can lock itself into the wedge hole。Wedge connections have gradually been replaced by threaded connections or other connections。
2015-02-06 Reading quantity 2804
introduction： IKOLinear bearing[IKOLinear bearing:“IKO”representative“Innovation,Know-how &Originality”。Needle roller bearings are produced in Japan、Linear bearings have the longest history、The most complete variety、The highest professional level of linear bearing manufacturers。Its products are widely used in machine tools and other industries。Our products have become the representative of high-quality brand-name products，Through the global marketing network to achieve user convenience、Fast service commitment。]After manufacturing and inspection，That is, cleaning and anti-embroidery treatment，Put it in the inner package
2015-02-06 Reading quantity 1471
introduction： one、Scheme overview Jinghe River330Kv power transmission and transformation project is one of the key projects in Shaanxi Province，The project is an important part of Shaanxi power grid，After the station is completed，Will replace220Qianfu Yanliang substation，Become an important power source for the region，It will also become an important hub substation of Shaanxi power grid。The project adopts international advancedIEC61850，IEC61850is“Substation communication network and system”The series of international standards，Represents substation automation system（SAS）The latest development direction。At present, the substation communication protocols widely used are mainlyIEC6
2015-02-06 Reading quantity 2798
introduction：In the forming process，Moisture control and the choice of molding processing conditions are the two most important factors affecting the quality of molded products，It is described below： Moisture control PCSimilar plastics will hydrolyze and break the bond even if they encounter very low moisture、The phenomenon of decreasing molecular weight and decreasing physical strength。So before the molding process，The moisture content of polycarbonate should be strictly controlled0.02%below，To avoid the reduction of mechanical strength of the molded product or the formation of bubbles on the surface、Abnormal appearance of silver grain, etc。To avoid abnormal conditions caused by water，Polycarbonate before processing，It should be dried by hot air dryer for more than three to five hours，Temperature setting
2015-02-06 Reading quantity 2792
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
