Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Zeroth law of thermodynamics: A law in thermodynamics that defines temperature based on the concept of heat balance。Usually expressed as﹕Between two systems in thermal equilibrium with a third system﹐Must be in thermal equilibrium。In the pictureA Diagram of the zeroth law of thermodynamics ﹑B Diagram of the zeroth law of thermodynamics ﹑C Diagram of the zeroth law of thermodynamics for 3A fixed mass and composition﹐And the thermal system is completely isolated from the outside world。interB ﹑C Separated by an insulating wall﹐At the same time make them separate fromA Thermal contact。stayA withB andA withC When they reach thermal equilibrium﹐reapplyB withC hair
2015-01-25 Reading quantity 2897
introduction：What oil is added to the planetary cycloidal pinwheel reducer？ If it comes from the factory，Its usually grease，Molybdenum disulfide is used-2orZL-2Lithium base grease and other grease。Because the reducer at the factory is for easy loading and unloading and transportation．Usually no lubricating oil is injected，Oil is only injected before use，Recommended at room temperatureN150Extreme pressure industrial gear oil。Lubricating oil change cycle：The reducer is in its first run200The first lubricating oil change must be carried out after hours，When replacing, there should be no residual oil。After the initial oil change,Work continuously every daylOMore than hours of speed reducer．Should be every other3Change the lubricating oil once every month、everyday
2015-01-25 Reading quantity 2965
introduction：Because the silver linear guide rail is a very precise product，Great care should be taken during use，Avoid scratching，Damage effect accuracy，Strict attention should be paid to the following matters when using
2015-01-25 Reading quantity 32864
introduction：productivity：180The root/when Pin diameterФ22 1、Comply with casting equipment general operating procedures。 2、pre-work，Start with a running test，Then run empty2-3minutes，Check the drive system（motor、Reducers and open gears）And whether the motion of the star wheel is smooth，Just make sure everythings okay，Before production can proceed。
2015-01-25 Reading quantity 2806
introduction： The process of combining and joining parts and components into mechanical products according to the technical requirements at the time of design。Mechanical assembly is an important process that finally determines the quality of mechanical products in mechanical manufacturing。Even if all qualified parts﹐If improperly assembled﹐Often can not form quality products。Simple products can be assembled directly from parts。Complex products must first assemble several parts into components﹐Called component assembly﹔Then several parts and some other parts are assembled into a complete product﹐Called total assembly。After product assembly
2015-01-25 Reading quantity 2803
introduction： Worm gear reducer is not done well in processing technology and material selection，It may cause transmission failure。It is also a problem that gear reducer manufacturers may encounter when producing parts，Such as hard reducer hardness does not meet the requirements，Screw lift bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Similar problems can occur when the design is not right
2015-01-25 Reading quantity 2907
introduction：kongjing celiang Aperture measurement inside diameter measurement Measurement of the diameter of the hole，Direct measurement、Indirect measurement and comprehensive measurement and other measurement methods。Aperture measurement is one of the main contents of length measurement technology。 Direct measurement utilizes two - or three-point positioning，Method of directly measuring the aperture,It is also the most commonly used aperture measurement method according to the precision grade size and quantity size of the aperture being measured,A universal length measuring tool capable of measuring the aperture can be used，For example, vernier calipers(
2015-01-25 Reading quantity 2792
introduction： The electromagnetic clutch has a simple structure，Therefore, it is also very convenient to install and maintain。However, in the process of use，The electromagnetic clutch will have different failures due to various factors，So what are the common types of electromagnetic clutch failures?The following is a simple introduction to the common faults of electromagnetic clutch Electromagnetic clutch general failure occurs in the start、Idling and loading，However, it occurs more in the start-up period，The main performance is that it cannot be started，Or the input electromagnetic clutch voltage is too low，The conventional input voltage isDC24V。And dynamic instability、
2015-01-25 Reading quantity 2793
introduction： Shrink packaging is the same as other mainstream packaging equipment，There are two types of intermittent and continuous。In the fierce market competition，Retailers are becoming more demanding，The quality of packing is of Paramount importance，All this has sparked another round of debate about shrink packaging。 On the one hand，biaxial（Batch type）Equipment suppliers dominate the market share；On the other hand，Single axis with medium speed（Continuous type）Equipment is also constantly impacting the market。 Yorkshire Packaging Systemscorporation（YPS）To the guest
2015-01-25 Reading quantity 2907
introduction：Laser rapid prototyping（Laser Rapid Prototyping：LRP）willCAD、CAM、CNC、laser、A new manufacturing technology that integrates advanced technologies such as precision servo drives and new materials。Compared with traditional manufacturing methods：The replicability of the prototype、High interchangeability；The manufacturing process has nothing to do with the geometry of the prototype；Short processing cycle、Low cost，Lower general manufacturing expenses50%，Process cycle reduction70%above；High technology integration，Realize the integration of design and manufacturing。 Recently developedLPRThere are mainly：Stereo light modeling(SLA) technology；
2015-01-25 Reading quantity 2892
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
